Abstract
The initial process design of a roll forming system is often based on the traditional ‘flower pattern diagram’. In this diagram, the cross sections of the strip at each roll stand are superimposed on a single plane; the diagram is a 2D representation of the 3D process. In the present work, the flower pattern is extended into three dimensions. To demonstrate the method, the forming path or trajectory of a point at the edge of the strip during forming a V-section is considered. The forming path is a surface curve that lies on a cylindrical surface having its axis along the machine axis. This surface is unwrapped to give its plane development and important features of the forming process can be determined and are readily interpreted from this plane curve. It is shown that at any stage in the process, the axial strain and the curvature of the sheet adjacent to the point are dependent on the slope of the trajectory in this plane projection. This new diagram, which apparently has not been used previously, provides a useful initial method of examining the roll forming process and optimising the flower pattern. The model is purely geometric, as is the original flower pattern approach, and does not include the effect of material behaviour. The concept is applied to several cases available in the literature. It shows that the lowest level of shape defect in the part is achieved when the trajectory of the strip edge follows the shortest line length between the start and finish of forming, leading to the least longitudinal strain introduced in the flange. This trend is in agreement with previous experimental observations, suggesting that the analytical model proposed may be applied for early process design and optimisation before time-consuming numerical analysis is performed.
Similar content being viewed by others
References
Halmos GT (ed) (2006) Roll forming handbook. Taylor & Francis, London
Angel RT (1949) Designing tools for cold roll forming. Iron Age 16:83–88
Noble CF, Sarantidis TM (1979) A study of cold roll forming. In: Abstracts 1st international conference on Rotary Metalworking Processes pp. 411–424
Bhattacharyya D, Smith PD, Yee CH, Collins IF (1984) The prediction of deformation length in cold roll-forming. J Mech Work Technol 9:181–191
Fong CK (1984) Cold roll forming. Master of Engineering, Department of Mechanical Engineering, Auckland University
Panton SM, Zhu SD, Duncan JL (1992) Geometric constraints on the forming path in roll forming channel sections. Proc Inst Mech Eng B J Eng Manuf 206:113–118
Panton SM, Zhu SD, Duncan JL (1994) Fundamental deformation types and sectional properties in roll forming. Int J Mech Sci 36:725–735
Lindgren M (2007) An improved model for the longitudinal peak strain in the flange of a rollformed U-channel developed by FE-analyses. Steel Res Int 78:82–87
Paralikas J, Salonitis K, Chryssolouris G (2011) Investigation of the effect of roll forming pass design on main redundant deformations on profiles from AHSS. Int J Adv Manuf Technol :1–17
Duncan JP, Duncan JL (1982) Folded developables. Proc R Soc Lond A Math Phys Sci 383:191–205
Lipschutz MM (1969) Differential geometry. McGraw-Hill, New York
Abeyrathna B, Rolfe B, Hodgson PD, Weiss M (2014) Effect of forming sequence on product straightness and springback in roll forming. Paper presented at the International Deep Drawing Research Group Conference 2014, Paris, France, 1–4 June 2014
Jimma T, Ona H (1980) Optimum roll-pass schedules on the cold roll-forming process of symmetrical channels, presented at the Int Mach Tool Des Res Conf, 21 st
Walker TR, Pick RJ (1990) Approximation of the axial strains developed during the roll forming of ERW pipe. J Mater Process Technol 22:29–44
Jeong SH, Lee SH, Kim GH, Seo HJ, Kim TH (2008) Computer simulation of U-channel for under-rail roll forming using rigid-plastic finite element methods. J Mater Process Technol 201:118–122
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Abeyrathna, B., Rolfe, B., Hodgson, P. et al. An extension of the flower pattern diagram for roll forming. Int J Adv Manuf Technol 83, 1683–1695 (2016). https://doi.org/10.1007/s00170-015-7667-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-7667-0